Chapter 3
WIA-COMM-008 covers wireless charging as a single engineering problem: moving power across an air gap between two coils, safely and with acceptable losses. The specification's range runs from a 5 W earbud case to electric-vehicle pads rated up to 350 kW. Everything in it follows from one mechanism, which is time-varying magnetic flux linking a transmitter coil and a receiver coil.
The inductive foundation starts with Faraday's law, ε = −N × dΦ/dt. In circuit terms, the voltage induced in the receiver is V₂ = M × dI₁/dt, where M is the mutual inductance and I₁ is the transmitter current. The specification ties M to the two self-inductances through the coupling coefficient k:
M = k × √(L₁ × L₂) k = 0 … 1
A designer controls k through four things the specification lists: distance, alignment, coil geometry (diameter, turns, wire gauge) and core material (air, ferrite, nanocrystalline). For circular coils k falls roughly with the cube of separation, and the specification gives an approximation in terms of the two coil radii and the gap d. Lateral offset is modelled separately as k(Δx) ≈ k₀ × exp(−α × Δx²). The decay constant α depends on coil geometry, so a large coil tolerates a given offset better than a small one. In practice this is why a phone that sits a few millimetres off-centre may charge more slowly or not at all.
Two further quantities govern how much of the coupled energy becomes useful power:
The overview in the standard also gives a compact relation, P = k × √(P₁ × P₂), where P₂ is the receiver's power capacity. Read it as a statement that transfer is bounded by both ends: a strongly coupled coil cannot deliver more than the receiver can accept.
The standard distinguishes simple induction from magnetic resonance, and the difference shows up in range, frequency and positioning freedom.
| Property | Inductive (Qi) | Resonant (AirFuel) |
|---|---|---|
| Principle | Electromagnetic induction between coils | Resonant magnetic coupling |
| Range | 0–10 mm | 0–50 mm |
| Typical efficiency | 70–85% | 60–80% |
| Frequency | 110–205 kHz consumer; 85 kHz EV | 6.78 MHz |
| Strength | Mature, widely adopted, cost-effective | Longer range, several devices, flexible placement |
| Limitation | Short range, precise alignment | Higher cost, larger components |
Resonance means tuning both sides so that inductive and capacitive reactance cancel at f₀ = 1 / (2π√(LC)). The specification's strongly coupled model bounds efficiency by η_max = (kQ)² / (1 + kQ)², with Q the geometric mean √(Q₁Q₂). The practical consequence is that a high-Q resonant system stays usable at a lower k, which is how it tolerates larger gaps and looser alignment.
Qi, developed by the Wireless Power Consortium, defines the consumer profiles. The Baseline Power Profile covers 0–5 W at 5 V and up to 1 A. The Extended Power Profile covers 5–15 W at 9 V or 12 V and up to 1.67 A. Qi v1.3 extends to 30 W for tablets and laptops. The operating frequency is stepped by the controller, f = f_base + (n × 64) Hz, so the transmitter adjusts power by moving along the resonance curve.
The receiver talks back over the same power link using load modulation (backscatter) at 2 kHz and 2 kbps. A Qi message is framed as follows:
[Preamble] [Header] [Message] [Checksum]
11 bits 1 byte 0-27 bytes 1 byte
A charge proceeds through six phases: selection (detect an object), ping (probe for a receiver), identification, configuration (negotiate the power level), power transfer under a control loop, and renegotiation. AirFuel instead uses a BLE side channel for pairing and control, and the specification's interoperability tests check resonance at 6.78 MHz ±5%.
The standard sorts the field by power level rather than by brand. The ladder below is the quickest way to see where each technology fits.
| Tier | Technology | Typical load | Frequency |
|---|---|---|---|
| 5 W | Qi BPP | Smartphones, earbuds | 110–205 kHz |
| 7.5 W | Qi BPP+ | Phones of the iPhone 8–12 generation | 110–205 kHz |
| 15 W | Qi EPP | Android flagships | 110–205 kHz |
| 30 W | Qi v1.3 | Laptops, tablets | 110–205 kHz |
| 50 W | AirFuel | Laptops | 6.78 MHz |
| EV classes | SAE J2954, ISO 19363 | Vehicles, up to 350 kW | 85 kHz |
The measured efficiency bands in the specification tell the same story. Qi BPP at 3–5 mm reaches 70–75%, and Qi EPP at 3–8 mm reaches 75–80%. AirFuel at 50 W works across 10–50 mm at 65–75%, and an 11 kW SAE J2954 system across 100–200 mm reaches 85–90%. Efficiency does not fall steadily with power. Large automotive pads are efficient because they are large, well-shielded and tuned to a fixed gap, whereas a phone charger gives up efficiency for convenience and low cost.
The EV classes are worth reading closely. The EV section of the specification lists WPT1 at 3.7 kW and 400 V (PHEV, small BEV), WPT2 at 7.7 kW and 400 V, WPT3 at 11 kW and 400 V, and WPT4 at 22 kW and 800 V. Elsewhere, shorter summary tables attach 11 kW and 22 kW to WPT1 and WPT2. Treat the EV section as the authoritative class table and confirm power classes against it before specifying hardware.
Three application patterns drive most of the standard's design guidance.
Consumer pads and alignment. Because k collapses with offset, the standard treats alignment as a user-interface problem as well as an electromagnetic one. Feedback comes in three forms. Visual feedback is an LED ring (red, yellow, green) or an app score. Auditory feedback speeds up the beeps or raises the pitch as alignment improves. Haptic feedback strengthens the vibration or raises the pulse rate. Systems that remove the user from the loop use magnets for passive alignment, motors for active coil positioning, cameras with computer vision, or arrays of coils where the best one is selected adaptively.
Multi-device charging. Three architectures are defined:
Power is shared by a simple rule, P_i = min(P_requested_i, P_max / N), so no device receives more than it asked for or more than an equal share of the charger's maximum. Where one driver serves several coils, time-division multiplexing switches between them at 10–100 Hz, with equal or priority-based duty cycles, which simplifies the power electronics.
Vehicles. In the SAE J2954 arrangement, a ground assembly (GA) with a coil 500–800 mm across is embedded in pavement. A vehicle assembly (VA) is mounted on the underside, with 100–250 mm of ground clearance. Both operate at 85 kHz. Alignment tolerances are stated as ±75 mm for WPT2 and ±100 mm for WPT3. Target GA-to-battery efficiency rises with class: above 85% for WPT2, above 88% for WPT3 and above 90% for WPT4. The same section describes dynamic charging, with several in-road coils switched on as the vehicle passes, at 20–100 kW per vehicle, aimed at electric buses and autonomous shuttles.
Wireless charging puts an oscillating magnetic field in an open space, so the specification gives safety the same weight as efficiency. It has three pillars.
Foreign object detection (FOD). Coins, keys and other metal can heat dangerously (above 100°C), reduce efficiency and damage the charger or receiver. The specification gives three detection methods:
| Method | Measure | Flag when |
|---|---|---|
| Q-factor | ΔQ = (Q_baseline − Q_measured) / Q_baseline | ΔQ > 10% |
| Power loss | P_loss = P_in − P_out − P_expected_loss | P_loss > 1 W |
| Frequency detuning | Δf = f_baseline − f_measured | Δf > 2% |
A Qi implementation calibrates a baseline Q with the surface empty, re-checks Q every second, cuts power on detection, and tells the user by LED, beep or app alert. A metal object shifts Q and resonance, and also appears as unexplained loss, so each method catches cases the others can miss. They work best in combination.
Thermal limits. Heat comes from coil I²R loss, core hysteresis and eddy currents, rectifier dissipation and induced heating in foreign objects. The specification calls for NTC thermistors embedded in the transmitter coil, sampled at 1–10 Hz, with a warning at 70°C and a cutoff at 80°C.
Field exposure. For 110–205 kHz the specification cites ICNIRP (2010) limits of 6.25 μT (RMS) magnetic field, 83 V/m (RMS) electric field and 2 W/kg localized SAR. It cites IEEE C95.1 (2019) limits of 27 μT and 614 V/m for 3 kHz–10 MHz. Mitigation uses ferrite behind the transmitter coil, aluminium shielding around sensitive electronics, distance, and lower current.
Certification. WPC Qi testing covers power levels, packet structure and timing, efficiency, FOD against standard metal objects, EMI/EMC, and temperature, overcurrent and overvoltage safety. AirFuel testing covers resonance, BLE pairing, multi-device operation, and EMF and thermal limits. Cross-platform testing runs devices against several charger brands, power levels and alignment offsets, from −10°C to 45°C. The standard's conformance endpoint returns a charger's Qi and AirFuel certification numbers, its SAE J2954 tier, its EMC report references and its EMF conformance in one record.
The implementation guidance for a transmitter runs in a deliberate order: select the power level (BPP, EPP or higher); choose the frequency (110 kHz for Qi, 6.78 MHz for AirFuel); design the coil (turns, wire gauge, ferrite); implement FOD; add an NTC sensor; design the power electronics (full-bridge inverter and controller); and implement communication, which means demodulating backscatter for Qi or using BLE for AirFuel. FOD and temperature sensing are placed before the power stage so they shape the design instead of being retrofitted.
The loss budget decides how well the design performs. The specification itemises coil resistance loss (I² × R), core loss (k_h × f × B² + k_e × f² × B²) and rectification loss (V_f × I + I² × R_on). Its optimization list follows from those terms: match impedance to the load, operate at resonance, minimise misalignment, use litz wire and ferrite shielding for high Q, and replace rectifier diodes with synchronous FETs.
The SDK and command-line tool wrap these calculations. For example:
wia-comm-008 calc-efficiency --input 15W --output 12W --distance 5mm
wia-comm-008 design-coil --power 15W --freq 110kHz --diameter 50mm
wia-comm-008 detect-fod --threshold 0.1 --baseline-impedance 50
wia-comm-008 optimize-align --offset-x 2mm --offset-y 3mm
wia-comm-008 calc-emf --power 15W --distance 10mm --freq 110kHz
Fielded chargers are managed through the Phase 2 HTTP interface. A charger is registered and fetched, a session is started, stopped and queried for state, and power and temperature telemetry arrives over a WebSocket:
POST /wireless-charging/v1/chargers
GET /wireless-charging/v1/chargers/{id}
POST /wireless-charging/v1/sessions
GET /wireless-charging/v1/sessions/{id}/state
POST /wireless-charging/v1/sessions/{id}/stop
WS /wireless-charging/v1/telemetry/stream
GET /wireless-charging/v1/conformance/{id}
Opening a session supplies the charger reference, a receiver descriptor (from NFC or BLE identity), a requested-power envelope, a target state of charge and the user's consent. The service checks compatibility first: a Qi-only charger rejects an AirFuel-only receiver unless it advertises multi-protocol support. The session then moves through negotiating, ramping, charging, topping-off and complete, or ends in aborted-fod, aborted-thermal or aborted-misalignment. The three abort states map directly onto the three safety pillars above. Telemetry carries Tx and Rx power, efficiency, coil temperatures, FOD status and an X/Y alignment estimate in millimetres, and alarms fire on FOD detection, a thermal threshold crossing or alignment loss. Session creation is rate-limited per charger to 10 per minute, which the specification gives as a defence against coil-thermal abuse.
The standard's own forward-looking items are specific. Spatial-freedom array chargers at 15–22 W and AirFuel zone chargers are the next step for multi-device surfaces. For them the API exposes the active-device list, per-device coil allocation, per-device power envelopes and the cross-talk envelope. Scheduling can favour low-battery or user-tagged devices.
For vehicles, dynamic charging is the larger shift. It changes the problem from aligning one parked pad to timing a sequence of coils against a moving receiver, with 20–100 kW delivered per vehicle. Buses and shuttles on fixed routes are the natural first users, because their paths are predictable and the road can be instrumented once. For both consumer and vehicle charging, the harmonisation of Qi, AirFuel, SAE J2954 and ISO 19363 is the stated aim, so a receiver works across charger brands and a charger works across receivers.
The physics sets the limits on how far this can go. The cubic fall of k with distance, the heating of foreign metal, and the field-exposure limits do not change with new products. Progress will come from better coils, better detection and better coordination between devices.
This chapter built the standard's picture of a wireless charger from the coil upward. Mutual inductance and the coupling coefficient explain power transfer. Resonance and high Q extend range at a cost in size and complexity. Qi's six-phase handshake and 2 kbps backscatter link let a receiver ask for the power it needs. FOD, thermal cutoffs and exposure limits keep that power from becoming a hazard. The power ladder, from 5 W earbuds to EV pads, shows that efficiency depends on matching coil size and gap to the load. The session and telemetry interface carries all of this to the operator, and its abort states reuse the same safety vocabulary.
A few figures from this chapter are worth keeping in mind: ΔQ above 10%, power loss above 1 W, detuning above 2%, a 70°C warning and an 80°C cutoff, and 85 kHz for vehicles against 110–205 kHz for consumer devices.
The next chapter moves from the charger's physics to its internals. It takes up coil construction, wire and ferrite choices, and the inverter and rectifier stages where the loss terms listed above are won or lost, and it shows how the efficiency and thermal targets of this chapter become component-level decisions.